Food Packaging
- All Products - Two-Piece Tinplate Cans - Three-Piece Tinplate Cans - Tinplate Lids & Ends - Twist-off Lug Cap - Aluminum Cans - Aluminum Ends & LidsCanned Food
- Canned Food Overview - Vegetables & Mushrooms - Fruits - Mushroom & Corn - Beans - Seafood & Ocean Vegetables - Glass JarRaw Materials & IQF Foods
- Frozen Foods - Dried Foods - Raw MaterialsBakery Ingredients
- Instant Dry Yeast - Condensed MilkCompany
About ZDA Contact Get a Quote
Ends run on dedicated conversion presses with controlled scoring depth, compound deposition and full dimensional verification. They fit our own can bodies or any third-party body — send the diameter, curl specification and seamer make.
All ends can be supplied plain, gold or aluminum lacquered, printed or with a customer-specific tab design.
| Parameter | Easy Open Ends (EOE) | Sanitary / Bottom / Peel-Off |
|---|---|---|
| Diameter range | 50 mm – 153 mm (200# – 603#) | 50 mm – 153 mm |
| Base material | ETP or TFS, 0.18 – 0.30 mm | ETP or aluminum, 0.16 – 0.28 mm |
| Opening design | SOT (stay-on tab), RPT (ring pull), full aperture, partial aperture | Peel-off aluminum membrane, full-open sanitary end, plain bottom end |
| Score residual | Controlled to ±5 µm | N/A |
| Opening force | 10 – 45 N (verified per run) | Peel force 8 – 25 N |
| Sealing compound | Water-based or solvent-based, applied for dry, aqueous, oily or retorted products | |
| Internal coating | Epoxy-phenolic, organosol, polyester, BPA-NI, aluminum-pigmented, sulphur-resistant | |
| External finish | Plain, clear or gold lacquer, up to 4-colour print | |
| Compatibility | Configured for Angelus, Ferrum, Soudronic and most regional seamers | |
| Packing | Sleeved stacks in cartons on pallets, or supplied in can-making wickets | |
Every end we tool for, matched to the can type it closes. Can type follows the industry COPE numbering; the figure beside it is the nominal body diameter in millimetres.
| Can Type (COPE) | Diameter (mm) | Aluminum EOE | Tinplate EOE | Normal Lid |
|---|---|---|---|---|
| 113# | - | ✓ | - | - |
| 200# | 50 | ✓ | ✓ | ✓ |
| 201# | 51 | ✓ | ✓ | ✓ |
| 202# | 52.3 | - | ✓ | ✓ |
| 209# | 63.0 | ✓ | ✓ | ✓ |
| 214# | 70 | - | ✓ | ✓ |
| 300# | 73 | ✓ | ✓ | ✓ |
| 305# | 78.0 | ✓ | ✓ | - |
| 307# | 83.3 | ✓ | ✓ | ✓ |
| 401# | 99 | ✓ | ✓ | ✓ |
| 403# | 102 | - | ✓ | ✓ |
| 404# | 105 | - | ✓ | - |
| 603# | 153.4 | ✓ | ✓ | ✓ |
✓ available · - not available in this can type. Ends outside this list are developed to drawing; tooling lead time 20–25 days.
Residual metal measured and logged every 30 minutes.
Initiation and full-open force tested on statistical samples.
Rivet pull-off and tab retention checked to specification limits.
Compound weight and placement verified for seam fill.
Trial seaming and teardown performed before release of each batch.
Tell us your diameter, seamer model and filling conditions — we will match the end to your line.